Return

Bright House Networks now provides three different DVR remotes with different features and programming capabilities. For correct programming instructions, look at the back of the remote to determine if your remote is a model AT8400-B, AT8400-D, or AT8550-B.

For AT8400-B models, click here.

For AT8400-D models, click here.

For AT8550-B models, click here.

Return

Programming the Digital Remote

Before your Digital Remote can be used to operate your TV, VCR and other devices, it must be programmed with the correct models. The instructions, along with the codes for your models, will allow you to program your Digital Remote to control your TV and VCR. If your model has more than one code listed, it may be necessary to try a few codes before your Digital Remote properly controls your TV, VCR and other devices.

To program the Digital Remote for your TV model

1. Locate the TV's setup code in TV Model Setup Codes for the Digital Remote.
2. Turn your TV on.
3. Holding the Digital Remote away from the TV, press and hold the TV and the SELECT buttons simultaneously until all the mode buttons blink twice.
4. Enter the first 4-digit code for your TV. All mode keys blink twice to indicate that the code entry was accepted.
5. Point the Digital Remote at the TV and press POWER to test the TV. If this did not work properly, repeat these steps using a different code.

To program the Digital Remote for your VCR model

1. Locate the VCR setup code in VCR Model Setup Codes for the Digital Remote.
2. Turn your VCR on.
3. Holding the Digital Remote away from your VCR, press and hold the VCR and the SELECT buttons until all the mode buttons at top blink twice.
4. Enter the first 4-digit code for your VCR. All mode keys blink twice to indicate that the code entry was accepted.
5. Point the Digital Remote at the VCR and press POWER to test the VCR. If this did not work properly, repeat these steps using a different code.

To program the Digital Remote for your CD Player, Stereo or other device

1. Locate the auxiliary device's setup code in Auxiliary Device Setup Codes for the Digital Remote.
2. Turn your CD Player, Stereo, or other device on.
3. Holding the Digital Remote away from the device, press and hold the AUX and SELECT buttons until all the mode buttons at top blink twice.
4. Enter the first 4-digit code for your CD Player, Stereo or other device. All mode keys blink twice to indicate that the code entry was accepted.
5. Point the Digital Remote at the device and press POWER to test the device. If this did not work properly, repeat these steps using a different code.

Choosing your Volume Control Source

Your Digital SmartBox or DVR and TV both have volume controls. It is possible to program your Digital Remote to control either of these volume levels. Follow the instructions to program your Digital Remote to control the desired device.

To program the Digital Remote to control the TV's volume

1. Holding Digital Remote away from Digital SmartBox or DVR, press and hold SELECT and CBL buttons until all the mode buttons at top blink twice.
2. Enter the code 993 slowly.
3. When the CBL mode key blinks twice, press the TV button on the Digital Remote to program the DVR remote to control the volume on the TV, or press the CBL button on the Digital Remote to control the volume on the Digital SmartBox or DVR.

Return

Programming the Digital Remote

Before your Digital Remote can be used to operate your TV, VCR and other devices, it must be programmed with the correct models. The instructions, along with the codes for your models, will allow you to program your Digital Remote to control your TV and VCR. If your model has more than one code listed, it may be necessary to try a few codes before your Digital Remote properly controls your TV, VCR and other devices.

To program the Digital Remote for your TV model

1. Locate the TV's setup code in TV Model Setup Codes for the Digital Remote.
2. Turn your TV on.
3. Holding the Digital Remote away from the TV, press and hold the TV and the SELECT buttons simultaneously until all the mode buttons blink twice.
4. Enter the first 4-digit code for your TV. All mode keys blink twice to indicate that the code entry was accepted.
5. Point the Digital Remote at the TV and press POWER to test the TV. If this did not work properly, repeat these steps using a different code.

To program the Digital Remote for your VCR model

1. Locate the VCR setup code in VCR Model Setup Codes for the Digital Remote.
2. Turn your VCR on.
3. Holding the Digital Remote away from your VCR, press and hold the VCR and the SELECT buttons until all the mode buttons at top blink twice.
4. Enter the first 4-digit code for your VCR. All mode keys blink twice to indicate that the code entry was accepted.
5. Point the Digital Remote at the VCR and press POWER to test the VCR. If this did not work properly, repeat these steps using a different code.

To program the Digital Remote for your CD Player, Stereo or other device

1. Locate the auxiliary device's setup code in Auxiliary Device Setup Codes for the Digital Remote.
2. Turn your CD Player, Stereo, or other device on.
3. Holding the Digital Remote away from the device, press and hold the AUX and SELECT buttons until all the mode buttons at top blink twice.
4. Enter the first 4-digit code for your CD Player, Stereo or other device. All mode keys blink twice to indicate that the code entry was accepted.
5. Point the Digital Remote at the device and press POWER to test the device. If this did not work properly, repeat these steps using a different code.

What If None of the Codes Work?

If none of the codes listed for your brand of device operate the device correctly, you can search through the code library for a valid code.

Searching the Code Library

1. Turn on the device.
2. Press and hold SELECT and the appropriate mode key (CBL, TV, VCR, or AUX) until the mode keys blink twice. For example, to search for a TV code, press and hold SELECT and TV at the same time.
3. Enter the code 991 slowly. The mode key you selected in step 2 blinks twice.
4. Point the remote toward the device, and press PLAY. The remote automatically tests each code in its library, beginning with the most common codes. The mode key blinks once each time the remote transmits a new code. The mode key blinks twice when it reaches the last code.
5. As soon as the device powers off, press SELECT.
6. Verify the new code is correct by pressing POWER. If the device powers on again, press SELECT to lock in the code. If the device does not power on, perform the following steps:
   
   1. Turn the device on.
   2. Press CH+ or CH- to step forward or backward one code at a time.
   3. When the device turns off, press SELECT to assign the code.

Improving Your Reaction Time

When you search the code library, you need to be ready to press SELECT as soon as the device turns off, but before the remote attempts to test the next code. Therefore, make sure you are familiar with the location of the SELECT key before you begin this procedure.

Which Code Worked?

After searching for your code automatically, it might be a good idea to make note of the correct code to save time in the event you need to reprogram your remote in the future.

1. Press and hold SELECT and the appropriate mode key (CBL, TV, VCR, or AUX) until the mode keys blink twice. For example, to search for a TV code, press and hold SELECT and TV at the same time.
2. Enter the code 991 slowly. The mode key you selected in step 1 blinks twice.
3. Press 1, then count the number of times the mode key blinks. The number of blinks indicates the first digit in the code. For example, 4 blinks indicates the first digit in the code is 4. If the mode key does not blink, the digit is 0.
4. Press 2, then count the number of times the mode key blinks. This number indicates the second number in the code.
5. Press 3, then count the number of times the mode key blinks. This number indicates the third number in the code.
6. Press 4, then count the number of times the mode key blinks. This number indicates the fourth number in the code.
7. After all four numbers in the code are identified, all mode keys blink three times. Write down and store your code for future reference. You may need it again if the device code is accidentally erased.

Reassign Mode Keys

If you are a big movie fan, you may want to control two video recording devices. Perhaps you have a DVD player and a VCR, or a VCR/DVD combination device. How can you control both the VCR and the DVD player when you only have one VCR key? With the AT8400-D, you can reassign a mode key to operate in a different mode. For example, you can reassign the AUX key to operate in VCR mode. Then, you can program the AUX key to control your DVD player. You can reassign the AUX key, the VCR key, or both. The TV key and the CBL key cannot be reassigned.

Reassigning Mode Keys

1. Press and hold SELECT and CBL until all mode keys blink twice.
2. Enter the code 992 slowly. The CBL mode key blinks twice.
3. Press the mode key associated with the type of device you want to control, and then press the mode key that you want to change. All mode keys blink three times. For example:
   
   • To program the AUX key to operate in VCR mode, press VCR and then AUX.
   • To program the VCR key to operate in TV mode, press TV and then VCR.

Change Power Control

Your remote is originally programmed in one of the following ways:

• The remote controls power for only one device at a time. For example, in CBL mode the POWER key controls the cable box only. However, in TV mode, the POWER key controls the TV only.
• The remote controls power for either one device or for multiple devices at once, based on the selected mode. For example, in CBL mode, the POWER key controls both the cable box and the TV at the same time.

Before you change how power control works, try your remote to see how the power control currently works. When trying out your remote, keep in mind that the remote provides a temporary override for power control. For example, if you press the TV key and then the POWER key within 3 seconds, the remote turns on the TV only, regardless of the programmed power settings. To see how the remote is originally programmed, wait at least 5 seconds before pressing the POWER key after you press any mode key.

Does your remote already control power for your cable box and TV at the same time? If not, Scientific-Atlanta strongly recommends that you program the remote to turn off the cable box each time you turn off your TV. Turning off the cable box is especially important for high-end cable boxes that contain hard drives for recording and storing TV programs and movies. Not only will you reduce wear and tear from the hard disk spinning constantly, but you'll also conserve electricity. As long as the cable box remains plugged in, the cable box will receive programming updates, and, if applicable, record programs and movies.

Controlling Power for Multiple Devices at Once

1. Press and hold SELECT and CBL until all mode keys blink twice.
2. Enter the code 998 slowly. The CBL key blinks twice.
3. Press the mode key for the first device in the group of devices you want to power on and off at once. The CBL key blinks twice.
4. Press the mode key for the second device in your power group. The CBL key blinks twice. Repeat for any other devices you want to control.
5. Press SELECT to save your power settings. All mode keys blink three times.

Controlling Power for One Device at a Time

Follow these steps to undo the steps performed above.

1. Press and hold SELECT and CBL until all mode keys blink twice.
2. Enter the code 998 slowly. The CBL key blinks twice.
3. Press SELECT to save your power settings. All mode keys blink three times.

Change Volume Control

Your remote is originally programmed in one of the following ways:

• The remote controls volume for one device, such as your TV, whether the remote is in TV, VCR, or CBL mode. The AUX mode always retains separate volume control.
• The remote controls volume for different devices, depending on the mode key you press. For example, in CBL mode, the volume keys control the cable box. However, in TV mode, the volume keys control the TV.

If you want to change the volume control, complete the procedure that fits your needs.

Controlling Volume for One Device

Note: If you want to assign volume control to a Scientific-Atlanta cable box, complete the following prerequisite steps. Press SETTINGS to access the General Settings on-screen menu. Then, verify that the Audio: Volume Control setting is set to Variable.

1. Press and hold SELECT and CBL until all mode keys blink twice.
2. Enter the code 993 slowly. The CBL key blinks twice.
3. Press the mode key for the device the volume keys should control. For example, if you want to control volume through your TV, press TV. All mode keys blink three times.

The volume keys control only one device whether you are in CBL, TV, or VCR mode. Note: In AUX mode, the remote always controls volume for the device assigned to the AUX key.

Controlling Volume for Different Devices

1. Press and hold SELECT and CBL until all mode keys blink twice.
2. Enter the code 993 slowly. The CBL key blinks twice.
3. Press SELECT. All mode keys blink three times.

After you select a mode, the volume keys control the device assigned to that mode. For example, in TV mode, the volume keys control volume for the TV only.

Change Channel Control

Your remote is originally programmed in one of the following ways:

• The remote controls channels for a single device, such as the cable box, whether the remote is in CBL, VCR, or TV mode. The AUX mode always retains separate channel control.
• The remote controls channels for different devices, depending on the mode key you press.

Controlling Channels For One Device

1. Press and hold SELECT and CBL until all mode keys blink twice.
2. Enter the code 997 slowly. The CBL key blinks twice.
3. Press the mode key associated with the device you want the channel keys to control. For example, if you want to assign channel control to your TV only, press TV. All mode keys blink three times.

The channel keys now always control the device associated with the mode you selected in this step, whether in TV, CBL, or VCR mode. In AUX mode, the remote always controls channels for the device assigned to the AUX key.

Controlling Channels For Different Devices

1. Press and hold SELECT and CBL until all mode keys blink twice.
2. Enter the code 997 slowly. The CBL key blinks twice.
3. Press SELECT. All mode keys blink three times.

The channel keys now control the device associated with the mode key you select. For example, in TV mode, the channel keys control the TV, but in CBL mode, the channel keys control the cable box.

Put It Back the Way I Got It

Resetting Mode Keys

You can reprogram the VCR key and the AUX key to operate in their original modes.

1. Press and hold CBL and SELECT until all mode keys blink twice.
2. Enter the code 992 slowly. The CBL key blinks twice.
3. Press either VCR or AUX twice to return that key to its original state. All mode keys blink three times.
4. Repeat this procedure if you want to return both keys to their original modes.

Resetting Device Codes and Mode Keys

Follow this procedure to return programmed device codes and mode keys to their original settings. This procedure erases device codes you programmed. In addition, this procedure returns all reassigned mode keys to their original operation.

1. Press and hold CBL and SELECT until all mode keys blink twice.
2. Enter the code 977 slowly. All mode keys blink three times. Then, after a few seconds the CBL key blinks twice.

Resetting Power, Volume, and Channel Control

Follow this procedure to return power, volume, and channel control to their original settings. This reset procedure does not reset any device codes you programmed or affect mode key reassignments.

1. Press and hold CBL and SELECT until all mode keys blink twice.
2. Enter the code 980 slowly. All mode keys blink three times.

Resetting All Changes

Follow this procedure to return the remote completely back to its original settings.

1. Press and hold CBL and SELECT until all mode keys blink twice.
2. Enter the code 981 slowly. All mode keys blink three times. Then, after a few seconds the CBL key blinks twice.

Return

Programming the Digital Remote

Your Digital Remote is initially programmed to only operate your cable box. The volume and mute keys will not work until a TV code is programmed into the Digital Remote. If the remote provides only limited functionality for a device, you can look for a code that provides more functionality. Before you begin, make sure you know the brand name of the device you want to control.

Note: Some remote keys may be assigned to operate one device only. For example, volume control may be assigned to the TV only. If this is the case, you can reprogram power, volume, and channel control using procedures further down this page.

To program the Digital Remote for your TV

1. Locate the TV setup code in TV Model Setup Codes for the Digital Remote.
2. Turn your TV on.
3. Holding the Digital Remote away from the TV, press and hold the TV and the SELECT buttons simultaneously until all the mode buttons blink twice.
4. Enter the first 4-digit code for your TV. All mode keys blink twice to indicate that the code entry was accepted.
5. Point the Digital Remote at the TV and press POWER to test the TV. If this did not work properly, repeat these steps using a different code.

To program the Digital Remote for your VCR

1. Locate the VCR setup code in VCR Model Setup Codes for the Digital Remote.
2. Turn your VCR on.
3. Holding the Digital Remote away from the VCR, press and hold the VCR and the SELECT buttons simultaneously until all the mode buttons blink twice.
4. Enter the first 4-digit code for your VCR. All mode keys blink twice to indicate that the code entry was accepted.
5. Point the Digital Remote at the VCR and press POWER to test the VCR. If this did not work properly, repeat these steps using a different code.

To program the Digital Remote for your DVD player

1. Locate the DVD setup code in DVD Model Setup Codes for the Digital Remote.
2. Turn your DVD player on.
3. Holding the Digital Remote away from the DVD player, press and hold the DVD and the SELECT buttons simultaneously until all the mode buttons blink twice.
4. Enter the first 4-digit code for your DVD player. All mode keys blink twice to indicate that the code entry was accepted.
5. Point the Digital Remote at the DVD player and press POWER to test the DVD player. If this did not work properly, repeat these steps using a different code.

To program the Digital Remote for your stereo ot other device

1. Locate the device setup code in Auxiliary Device Setup Codes for the Digital Remote.
2. Turn your device on.
3. Holding the Digital Remote away from the device, press and hold the AUX and the SELECT buttons simultaneously until all the mode buttons blink twice.
4. Enter the first 4-digit code for your device. All mode keys blink twice to indicate that the code entry was accepted.
5. Point the Digital Remote at the device and press POWER to test the device. If this did not work properly, repeat these steps using a different code.

What if none of the codes worked?

If none of the codes listed for your brand of device operate the device correctly, you can search through the code library for a valid code.

Searching the Code Library

1. Turn on the device.
2. Press and hold SELECT and the appropriate mode key (CBL, TV, DVD, VCR, or AUX) until the mode keys blink twice. For example, to search for a TV code, press and hold SELECT and TV at the same time.
3. Enter the code 991 slowly. The mode key you selected in step 2 blinks twice.
4. Point the remote toward the device, and press PLAY. The remote automatically tests each code in its library, beginning with the most common codes. The mode key blinks once each time the remote transmits a new code. The mode key blinks twice when it reaches the last code.
5. As soon as the device powers off, press SELECT.
6. Verify the new code is correct by pressing POWER. If the device powers on again, press SELECT to lock in the code. If the device does not power on, perform the following steps:
   
   1. Turn the device on.
   2. Press CH+ or CH- to step forward or backward one code at a time.
   3. When the device turns off, press SELECT to assign the code.

Improving Your Reaction Time

When you search the code library, you need to be ready to press SELECT as soon as the device turns off, but before the remote attempts to test the next code. Therefore, make sure you are familiar with the location of the SELECT key before you begin this procedure.

Which Code Worked?

After searching for your code automatically, it might be a good idea to make note of the correct code to save time in the event you need to reprogram your remote in the future.

1. Press and hold SELECT and the appropriate mode key (CBL, TV, VCR, or AUX) until the mode keys blink twice. For example, to search for a TV code, press and hold SELECT and TV at the same time.
2. Enter the code 990 slowly. The mode key you selected in step 1 blinks twice.
3. Press 1, then count the number of times the mode key blinks. The number of blinks indicates the first digit in the code. For example, 4 blinks indicates the first digit in the code is 4. If the mode key does not blink, the digit is 0.
4. Press 2, then count the number of times the mode key blinks. This number indicates the second number in the code.
5. Press 3, then count the number of times the mode key blinks. This number indicates the third number in the code.
6. Press 4, then count the number of times the mode key blinks. This number indicates the fourth number in the code.
7. After all four numbers in the code are identified, all mode keys blink three times. Write down and store your code for future reference. You may need it again if the device code is accidentally erased.

Reassign Mode Keys

If you are a big movie fan, you may want to control two video recording devices. Perhaps you have a DVD player and a VCR, or a VCR/DVD combination device. How can you control both the VCR and the DVD player when you only have one VCR key? With the AT8400-D, you can reassign a mode key to operate in a different mode. For example, you can reassign the AUX key to operate in VCR mode. Then, you can program the AUX key to control your DVD player. You can reassign the AUX key, the VCR key, or both. The TV key and the CBL key cannot be reassigned.

Reassigning Mode Keys

1. Press and hold SELECT and CBL until all mode keys blink twice.
2. Enter the code 992 slowly. The CBL mode key blinks twice.
3. Press the mode key associated with the type of device you want to control, and then press the mode key that you want to change. All mode keys blink three times. For example:
   
   • To program the AUX key to operate in VCR mode, press VCR and then AUX.
   • To program the VCR key to operate in TV mode, press TV and then VCR.

Change Power Control

Your remote is originally programmed in one of the following ways:

• The remote controls power for only one device at a time. For example, in CBL mode the POWER key controls the cable box only. However, in TV mode, the POWER key controls the TV only.
• The remote controls power for either one device or for multiple devices at once, based on the selected mode. For example, in CBL mode, the POWER key controls both the cable box and the TV at the same time.

Before you change how power control works, try your remote to see how the power control currently works. When trying out your remote, keep in mind that the remote provides a temporary override for power control. For example, if you press the TV key and then the POWER key within 3 seconds, the remote turns on the TV only, regardless of the programmed power settings. To see how the remote is originally programmed, wait at least 5 seconds before pressing the POWER key after you press any mode key.

Does your remote already control power for your cable box and TV at the same time? If not, Scientific-Atlanta strongly recommends that you program the remote to turn off the cable box each time you turn off your TV. Turning off the cable box is especially important for high-end cable boxes that contain hard drives for recording and storing TV programs and movies. Not only will you reduce wear and tear from the hard disk spinning constantly, but you'll also conserve electricity. As long as the cable box remains plugged in, the cable box will receive programming updates, and, if applicable, record programs and movies.

Controlling Power for Multiple Devices at Once

1. Press and hold SELECT and CBL until all mode keys blink twice.
2. Enter the code 998 slowly. The CBL key blinks twice.
3. Press the mode key for the first device in the group of devices you want to power on and off at once. The CBL key blinks twice.
4. Press the mode key for the second device in your power group. The CBL key blinks twice. Repeat for any other devices you want to control.
5. Press SELECT to save your power settings. All mode keys blink three times.

Controlling Power for One Device at a Time

Follow these steps to undo the steps performed above.

1. Press and hold SELECT and CBL until all mode keys blink twice.
2. Enter the code 998 slowly. The CBL key blinks twice.
3. Press SELECT to save your power settings. All mode keys blink three times.

Change Volume Control

Your remote is originally programmed in one of the following ways:

• The remote controls volume for one device, such as your TV, whether the remote is in TV, DVD, VCR, or CBL mode. The AUX mode always retains separate volume control.
• The remote controls volume for different devices, depending on the mode key you press. For example, in CBL mode, the volume keys control the cable box. However, in TV mode, the volume keys control the TV.

If you want to change the volume control, complete the procedure that fits your needs.

Controlling Volume for One Device

Note: If you want to assign volume control to a Scientific-Atlanta cable box, complete the following prerequisite steps. Press SETTINGS to access the General Settings on-screen menu. Then, verify that the Audio: Volume Control setting is set to Variable.

1. Press and hold SELECT and CBL until all mode keys blink twice.
2. Enter the code 993 slowly. The CBL key blinks twice.
3. Press the mode key for the device the volume keys should control. For example, if you want to control volume through your TV, press TV. All mode keys blink three times.

The volume keys control only one device whether you are in CBL, TV, DVD, or VCR mode. Note: In AUX mode, the remote always controls volume for the device assigned to the AUX key.

Controlling Volume for Different Devices

1. Press and hold SELECT and CBL until all mode keys blink twice.
2. Enter the code 993 slowly. The CBL key blinks twice.
3. Press SELECT. All mode keys blink three times.

After you select a mode, the volume keys control the device assigned to that mode. For example, in TV mode, the volume keys control volume for the TV only.

Change Channel Control

Your remote is originally programmed in one of the following ways:

• The remote controls channels for a single device, such as the cable box, whether the remote is in CBL, DVD, VCR, or TV mode. The AUX mode always retains separate channel control.
• The remote controls channels for different devices, depending on the mode key you press.

Controlling Channels For One Device

1. Press and hold SELECT and CBL until all mode keys blink twice.
2. Enter the code 997 slowly. The CBL key blinks twice.
3. Press the mode key associated with the device you want the channel keys to control. For example, if you want to assign channel control to your TV only, press TV. All mode keys blink three times.

The channel keys now always control the device associated with the mode you selected in this step, whether in TV, DVD, CBL, or VCR mode. In AUX mode, the remote always controls channels for the device assigned to the AUX key.

Controlling Channels For Different Devices

1. Press and hold SELECT and CBL until all mode keys blink twice.
2. Enter the code 997 slowly. The CBL key blinks twice.
3. Press SELECT. All mode keys blink three times.

The channel keys now control the device associated with the mode key you select. For example, in TV mode, the channel keys control the TV, but in CBL mode, the channel keys control the cable box.

Change VCR/VOD Programming

Your remote is originally programmed in one of the following ways:

• The Rewind, Play, Fast Forward, Stop, Pause, and Record keys (the "transport keys") are programmed, by default, to transmit the codes for the Explorer 8000 series Home Entertainment Server video-on-demand (VOD) or Digital Video Recorder (DVR) functions when in Cable (CBL) mode.
• The transport keys control different devices, depending on the mode key you press.

You can choose to override the default settings for the transport keys to that the transport keys operate a different device when you have selected CBL mode. Try your remote to see how the transport keys currently work. If you want to change the settings for the transport keys, complete the procedure that fits your needs.

Changing VCR/VOD Programming

1. Pres and hold CBL and SELECT until all mode keys blink twice.
2. Enter the code 999 slowly. The CBL key blinks twice.
3. Pres the mode key associated with the device you want the transport keys to now control. All mode keys blink three times.

Results:

• The transport keys now always control the device associated with the mode you selected in this procedure.
• Pressing PLAY starts the VCR, DVD, or the device that has been reassigned to AUX.
• In AUX mode, the remote always controls channels for the device assigned to the AUX key.

Restoring default VCR/VOD Programming

1. Press and hold CBL and SELECT until all mode keys blink twice.
2. Enter the code 999 slowly. The CBL key blinks twice.
3. Press CBL. All mode keys blink three times.

Result: The transport keys are restored to their default settings.

Put It Back the Way I Got It

Resetting Mode Keys

You can reprogram the VCR key and the AUX key to operate in their original modes.

1. Press and hold CBL and SELECT until all mode keys blink twice.
2. Enter the code 992 slowly. The CBL key blinks twice.
3. Press either VCR or AUX twice to return that key to its original state. All mode keys blink three times.
4. Repeat this procedure if you want to return both keys to their original modes.

Resetting Device Codes and Mode Keys

Follow this procedure to return programmed device codes and mode keys to their original settings. This procedure erases device codes you programmed. In addition, this procedure returns all reassigned mode keys to their original operation.

1. Press and hold CBL and SELECT until all mode keys blink twice.
2. Enter the code 977 slowly. All mode keys blink three times. Then, after a few seconds the CBL key blinks twice.

Resetting Power, Volume, and Channel Control

Follow this procedure to return power, volume, and channel control to their original settings. This reset procedure does not reset any device codes you programmed or affect mode key reassignments.

1. Press and hold CBL and SELECT until all mode keys blink twice.
2. Enter the code 980 slowly. All mode keys blink three times.

Resetting All Changes

Follow this procedure to return the remote completely back to its original settings.

1. Press and hold CBL and SELECT until all mode keys blink twice.
2. Enter the code 981 slowly. All mode keys blink three times. Then, after a few seconds the CBL key blinks twice.